Sapphire Plug-ins for Autodesk: WipeDoubleWedge

WipeDoubleWedge

In the S_Wipes Plugin.

Performs a wipe transition between two input clips using two wedge shapes. The Wipe Amt parameter should be animated to control the transition speed. Increase the Border Width parameter to draw a border at the wipe transition edges.

Inputs:

From: Starts the transition with this clip.

To: Ends the transition with this clip.

Parameters:

Load Preset: Push-button .
Brings up the Preset Browser to browse all available presets for this effect.

Save Preset: Push-button .
Brings up the Preset Save dialog to save a preset for this effect.

Wipe Amt: AutoTransition,  Default: 0, Range: -0.5 to 1.5, Shared .
The transition ratio between the From and To inputs. A value of 0 gives only the From input and a value of 1 gives only the To input. By default this parameter will automatically animate from 0 to 1 to perform a complete wipe.

Angle: Default: 0, Range: any.
The rotation angle of the wedge shapes in counter-clockwise degrees.

Sharpness: Default: 2, Range: 0 or greater.
The sharpness of the point of the wedges.

Wipe Direction: Popup menu,  Default: Wedge In .
Selects the direction of the motion of the wedges.
Wedge In: the wedge contains the first image and shrinks inwards.
Wedge Out: the wedge contains the second image and grows outwards.

Edge Softness: Default: 0, Range: 0 or greater, Shared .
The width of the transition edges. Larger values will cause softer, less visible edges in the wipe pattern.

Border Width: Default: 0, Range: 0 or greater, Shared .
If positive, a colored border is drawn at the wipe transition edges, using the border color, opacity, softness, and shift parameters below.

Border Color: Default rgb: [0.75 0.75 0.75], Shared .
The color of the border. This has no effect unless Border Width is positive.

Border Opacity: Default: 1, Range: 0 to 1, Shared .
The opacity of the border. Decrease to make the border transparent and allow the image under it to show through. This has no effect unless Border Width is positive.

Border Softness: Default: 0, Range: 0 or greater, Shared .
The softness of the border edges. This has no effect unless Border Width is positive.

Border Shift: Default: 0, Range: any, Shared .
Shifts the border ahead of or behind the transition edge. This has no effect unless Border Width is positive.

Params2:

Params3:

Border Glow: Default: 0, Range: 0 or greater.
Adds a glow along the border of the wipe. The value determines the brightness of the glow.

Glow Color: Default rgb: [1 1 1].
The color of the glowing border.

Glow Width: Default: 0.1, Range: 0 or greater.
The width of the glowing border.

Width Red: Default: 1, Range: 0 or greater.
Scales the red glow width. If the red, green, and blue widths are all equal, the glow will match Glow Color. Otherwise it will have a fringe of varying color.

Width Green: Default: 1.2, Range: 0 or greater.
Scales the green glow width.

Width Blue: Default: 1.4, Range: 0 or greater.
Scales the blue glow width.

Noise Amp: Default: 1, Range: 0 or greater.
The amount of noise to add to the glowing border.

Noise Freq: Default: 16, Range: 0.1 to 20.
The spatial frequency of the noise.

Noise Speed: Default: 2, Range: any.
The speed with which the noise changes or boils over time.
See general info for: Res , On Fields , Redraw , Undo , Load Defaults , Crop , Add Noise , and Use Gamma .


See Also:

WipeLine
WipeCircle
WipeRectangle
WipeStar
WipeClock
WipeWedge
WipeFourWedges
WipeDots
WipeChecker
WipeStripes
WipeRings
WipeBlobs
WipeCells
WipeTiles
WipePixelate
WipeDiffuse
WipeBubble
WipeClouds
WipeMoire
WipePlasma
WipePointalize
WipeWeave
WipeFlux
Sapphire Plug-ins Introduction

PRODUCT UPDATES & SPECIAL OFFERS

Join our email newsletter and keep up to date