Sapphire Plug-ins for Autodesk: Swish3D

Wipes: Swish3D

In the S_Wipes Plugin.

Dissolves between two input clips while performing 3D moves on each. During the transition the From clip is transformed by the Zdist, Rotate, Swivel, Tilt, Shift, Scale, and Shear parameters, and the To clip is transformed by the opposite of these values. The overall amount of motion for each image can be scaled by the Rel Amp From and Rel Amp To parameters.

Inputs:

From: Starts the transition with this clip.

To: Ends the transition with this clip.

Parameters:

Load Preset: Push-button .
Brings up the Preset Browser to browse all available presets for this effect.

Save Preset: Push-button .
Brings up the Preset Save dialog to save a preset for this effect.

Amount: AutoTransition,  Default: 0, Range: -0.5 to 1.5, Shared .
The transition ratio between the From and To inputs. A value of 0 gives only the From input and a value of 1 gives only the To input. By default this parameter will automatically animate from 0 to 1 to perform a complete wipe.

Motion Blur: Default: 1, Range: 0 or greater.
Scales the amount of motion blur to use.

Center: X & Y,   Default: [0 0], Range: any.
The location of the d center in screen coordinates relative to the center of the frame. This parameter can be set by enabling and moving the Center Widget. Note that moving the d center can also cause the d size to change so that the current value of Wipe Amt remains correct.

Z Dist: Default: 0.1, Range: -1 or greater.
The 'distance' to transform the From clip. Values greater than 1.0 move it farther away and make it smaller. Values less then 1.0 move the image closer and enlarge it. By default, the To clip is also transformed by the opposite of this value.

Rotate: Default: 0, Range: any.
Rotates by the specified angle in counter-clockwise degrees.

Fade: Popup menu,  Default: From and To .
Determines which clips are faded in or out during the transition.
From and To: Cross fades both clips during the transition.
Only From: Fades out the From clip and composites that over the To clip. This causes the To clip to remain fully opaque in areas where the From clip does not overlap with it.
Only To: Fades in the To clip and composites that over the From clip. This causes the From clip to remain fully opaque in areas where the To clip does not overlap with it.

Slow In: Default: 0.5, Range: 0 or greater.
If positive, causes the transition to start more gradually.

Slow Out: Default: 0.5, Range: 0 or greater.
If positive, causes the transition to end more gradually.

Shift: X & Y,   Default: [0 0], Range: any.
Translation of the d pattern.

Scale: Default: 1, Range: 0 or greater.
Scales the size of the clips.

Fade Mid Time: Default: 0.5, Range: 0 to 1.
The midpoint in time of the image dissolve. Decrease for an earlier dissolve or increase for a later dissolve. If this is 1.0 the From clip will remain fully opaque for the entire transition. You can use this in combination with the Combine parameter to create various reveals without fading either clip. For example set Dissolve Mid Time to 1.0, Combine to Fade From, and then Shift and/or Rotate to cause the From clip to move off the screen.

Swivel: Default: 0, Range: -90 to 90.
Rotates left or right in 3D about a vertical axis.

Tilt: Default: 0, Range: -90 to 90.
Rotates up or down in 3D about a horizontal axis. You can use Swivel and Tilt together to rotate about arbitrary diagonal axes.

Perspective Amt: Default: 1, Range: 0.25 to 4.
Controls the amount of lens telescoping while applying Swivel and Tilt. Increase for more 3D perspective.

Brightness: Default: 1, Range: 0 or greater.
Scales the brightness of the result. This can be animated to brighten the result during the transition, but should typically start and end at 1.0 to avoid any pop at the start or end of the transition.

Mid Brightness: Default: 1, Range: 0 or greater.
Scales the brightness of the result at the middle of the transition by this amount. Automatically ramps to this brightness and then back again during the transition.

Params2:

Rel Amp From: Default: 1, Range: any.
Scales the amount of transformation applied to the From clip. Set to zero to disable moving the From clip. Make negative to reverse the motion.

Rel Amp To: Default: -1, Range: any.
Scales the amount of transformation applied to the To clip. By default, the To clip is transformed in the opposite direction of the From clip. Set to zero to disable moving the To clip. Make positive to move the To clip in the same direction as the From clip.

Scale Rel: X & Y,   Default: [1 1], Range: 0 or greater.
Scales the relative horizontal or vertical size of the clips.

Shear: X & Y,   Default: [0 0], Range: any.
Shears horizontally or vertically.

Wrap From: X & Y,  Popup menu,  Default: [ Reflect Reflect ].
Determines the method for accessing outside the borders of the From image.
No: gives black beyond the borders.
Tile: repeats a copy of the image.
Reflect: repeats a mirrored copy. Edges are often less visible with this method.

Wrap To: X & Y,  Popup menu,  Default: [ Reflect Reflect ].
Determines the method for accessing outside the borders of the To image.
No: gives black beyond the borders.
Tile: repeats a copy of the image.
Reflect: repeats a mirrored copy. Edges are often less visible with this method.

Filter: Check-box,  Default: on.
If enabled, the image is adaptively filtered when it is resampled. This gives better quality results when the image is warped smaller.
See general info for: Res , On Fields , Redraw , Undo , Load Defaults , Crop , Add Noise , and Use Gamma .


See Also:

WipeLine
WipeCircle
WipeRectangle
WipeStar
WipeClock
WipeWedge
WipeDoubleWedge
WipeFourWedges
WipeDots
WipeChecker
WipeStripes
WipeRings
WipeBlobs
WipeCells
WipeTiles
WipePixelate
WipeDiffuse
WipeBubble
WipeClouds
WipeMoire
WipePlasma
WipePointalize
WipeWeave
WipeFlux
Sapphire Plug-ins Introduction

PRODUCT UPDATES & SPECIAL OFFERS

Join our email newsletter and keep up to date