PixelSortMask: Radial In the S_PixelSortMask Plugin. Inputs: Source: The clip to be processed. Mask: Interpolate between the result and the Source input. White areas use the result of the effect. Black areas use the Source clip.

Parameters:

Load Preset: Push-button .
Brings up the Preset Browser to browse all available presets for this effect.

Save Preset: Push-button .
Brings up the Preset Save dialog to save a preset for this effect.

Start Angle: Default: 0, Range: any.

Degrees Sorted: Default: 360, Range: 0 to 360.

Center: X & Y,   Default: [0 0], Range: any.

Threshold: Default: 0.3, Range: any, Shared .

Sort Direction: Popup menu,  Default: sort above threshold .

sort below threshold:

sort above threshold:

Reverse Sort Direction: Check-box,  Default: off, Shared .

Sort Type: Popup menu,  Default: monochrome .

monochrome:

average:

minimum:

maximum:

red:

green:

blue:

hue:

saturation:

brightness:

Random Sort Restart: Default: 100, Range: 0 to 1000, Shared .

Soft Threshold Mask: Default: 0.1, Range: 0 or greater, Shared .

Mix With Source: Default: 0, Range: 0 to 1, Shared .
Interpolates between the result (0) and the original source (1).

Seed: Default: 0.273, Range: 0 or greater, Shared .
Used to initialize the random number generator. The actual seed value is not significant, but different seeds give different results and the same value should give a repeatable result.

Show: Popup menu,  Default: Result .

Result:

Raw Sort Values:

Threshold Mask:

Random Restart Noise:

Combined Mask:

Ray Length: Default: 0.8, Range: 0 or greater.

Inner Radius: Default: 0.1, Range: 0 or greater.

Vary Radius: Default: 0.1, Range: 0 to 1.

Mask Use: Popup menu,  Default: Luma .
Determines how the Mask input channels are used to make a monochrome mask.

Luma: the luminance of the RGB channels is used.

Alpha:

Blur Mask: Default: 0.05, Range: 0 or greater, Shared .
Blurs the Mask input by this amount before using. This can provide a smoother transition between the masked and unmasked areas.

Invert Mask: Check-box,  Default: off, Shared .
If enabled, inverts the mask input so the effect is applied to areas where the Mask is black instead of white.

Params2:

Params3:

Mocha: Default: 0, Range: 0 or greater, Shared .
Brings up the Mocha window for tracking footage and generating masks.

Blur Mocha: Default: 0, Range: 0 or greater, Shared .
Blurs the Mocha Mask by this amount before using. This can be used to soften the edges or quantization artifacts of the mask, and smooth out the time displacements.

Mocha Opacity: Default: 1, Range: 0 to 1, Shared .
Controls the strength of the Mocha mask. Lower values reduce the intensity of the effect.

Invert Mocha: Check-box,  Default: off, Shared .
If enabled, the black and white of the Mocha Mask are inverted before applying the effect.

Show Mocha Only: Check-box,  Default: off, Shared .
Bypass the effect and show the Mocha Mask itself.

Bypass Mocha: Check-box,  Default: off, Shared .
Ignore the Mocha Mask and apply the effect to the entire source clip.

Combine Masks: Popup menu,  Default: Union .
Determines how to combine the Mocha Mask and Input Mask when both are supplied to the effect.

Union: Uses the area covered by both masks together.

Intersect: Uses the area that overlaps between the two masks.

Mocha Only: Ignore the Input Mask and only use the Mocha Mask.

See general info for: Res , On Fields , Redraw , Undo , Load Defaults , Crop , Add Noise , and Use Gamma .

See Also:

Sapphire Plug-ins Introduction