Sapphire Plug-ins for Autodesk: WarpBubble


In the S_Warps Plugin.

Warps the source clip by a smooth noise function. This can be used to create heat diffusion or under water types of effects. The Shift Speed parameters cause the noise pattern to automatically translate over time. Adjust the Amplitude and Frequency parameters to give different types of distortions.


Source: The input clip to be warped.


Load Preset: Push-button .
Brings up the Preset Browser to browse all available presets for this effect.

Save Preset: Push-button .
Brings up the Preset Save dialog to save a preset for this effect.

Frequency: Default: 16, Range: 0.01 or greater.
The frequency of the noise pattern. Increase for more and smaller bubbles, decrease for fewer and larger bubbles.

Frequency Rel X: Default: 1, Range: 0.01 or greater.
The relative horizontal frequency of the bubble pattern. Increase for taller bubbles, decrease for wider ones.

Amplitude: Default: 0.25, Range: any.
Scales the amount of warping distortion. Increase for more severe distortion.

Octaves: Integer,  Default: 1, Range: 1 to 10.
The number of summed layers of noise. Each octave is twice the frequency and half the amplitude of the previous. A single octave gives a smooth texture. Adding octaves makes the result approach a fractal (1/f) noise texture.

Seed: Default: 0.23, Range: 0 or greater.
Used to initialize the random number generator. The actual seed value is not significant, but different seeds give different results and the same value should give a repeatable result.

Shift Start: X & Y,   Default: [0 0], Range: any.
The translation of the bubble pattern.

Shift Speed: X & Y,   Default: [0.1 0], Range: any.
If non-zero, the bubble pattern is automatically animated to shift at this speed. The result of animated Speed values may not be intuitive, so for variable speed motion it is usually best to set this to 0 and animate the Shift Start values instead.

Z Dist: Default: 1, Range: 0.01 or greater.
Scales the 'distance' of the image. Values greater than 1.0 move it farther away and make it smaller. Values less than 1.0 move the image closer and enlarge it. Zooming in slightly can sometimes be used to hide edge artifacts.

Filter: Check-box,  Default: on.
If enabled, the image is adaptively filtered when it is resampled. This gives a better quality result when parts of the image are warped smaller.

Rotate Warp Dir: Default: 0, Range: any.
Rotation angle of the warping directions in counter-clockwise degrees.

Wrap: X & Y,  Popup menu,  Default: [ Reflect Reflect ].
Determines the method for accessing outside the borders of the source image.
No: gives black beyond the borders.
Tile: repeats a copy of the image.
Reflect: repeats a mirrored copy. Edges are often less visible with this method.



Mocha: Default: 0, Range: 0 or greater, Shared .
Brings up the Mocha window for tracking footage and generating masks.

Blur Mocha: Default: 0, Range: 0 or greater, Shared .
Blurs the Mocha Mask by this amount before using. This can be used to soften the edges or quantization artifacts of the mask, and smooth out the time displacements.

Mocha Opacity: Default: 1, Range: 0 to 1, Shared .
Controls the strength of the Mocha mask. Lower values reduce the intensity of the effect.

Invert Mocha: Check-box,  Default: off, Shared .
If enabled, the black and white of the Mocha Mask are inverted before applying the effect.

Show Mocha Only: Check-box,  Default: off, Shared .
Bypass the effect and show the Mocha Mask itself.

Bypass Mocha: Check-box,  Default: off, Shared .
Ignore the Mocha Mask and apply the effect to the entire source clip.
See general info for: Res , On Fields , Redraw , Undo , Load Defaults , Crop , Add Noise , and Use Gamma .

See Also:

Sapphire Plug-ins Introduction


Join our email newsletter and keep up to date