Sapphire Plug-ins for AVX2: DissolveTiles

S_DissolveTiles

Transitions between two input clips while breaking each up into tiles and scrambling them. The first clip breaks apart and spreads out while the second clip coalesces behind the first. The Dissolve Amount parameter should be animated to control the transition speed.

In the Sapphire Transitions category.


Inputs:

From: Starts the transition with this clip.

To: Ends the transition with this clip.

Parameters:

Load Preset: Push-button .
Brings up the Preset Browser to browse all available presets for this effect.

Save Preset: Push-button .
Brings up the Preset Save dialog to save a preset for this effect.

Dissolve Amount: Default: 0, Range: 0 to 1.
The transition ratio between the From and To inputs. Auto Trans must be disabled for this parameter to be used. This would normally be animated from 0 to 1 to perform a complete transition, and the curve can be adjusted for more detailed control over the timing of the dissolve. The Slow In and Slow Out parameters, if positive, also adjust the transition ratio internally for a smoother start and/or end to the transition.

Scramble Speed: Default: 2, Range: any.
The amount each input should be scrambled at the edges of the transiton. The incoming clip is scrambled by this amount at the beginning of the transition, and the outgoing clip is scramble by this amount at the end. Setting this to zero will result in no tiling on either clip.

Scramble Rel: X & Y,   Default: [1 1], Range: 0 or greater.
The relative amounts of horiztonal and vertical scrambling.

Scramble Rel From: Default: 1, Range: any.
The relative amount of scrambling in the outgoing clip. Set this to zero if the outgoing clip shouldn't be scrambled at all.

Scramble Rel To: Default: -1, Range: any.
The relative amount of scrambling in the incoming clip. Set this to zero if the incoming clip shouldn't be scrambled at all.

Tiles: Default: 10, Range: 1 or greater.
How many tiles across the image. Increase for many tiny tiles; decrease for a few large ones.

Tile Rel Width: Default: 1, Range: 0.01 or greater.
Scales the height of each tile.

Tile Rel Height: Default: 1, Range: 0.01 or greater.
Scales the width of each tile.

Rotate Warp Dir: Default: 0, Range: any.
Rotates the warping direction by this many degrees. Animate to rotate the tiles around for an interesting effect.

Dissolve Delay: Default: 0.6, Range: 0 to 1.
The delay before cross-dissolving between the From and To clips. If this is set to 1, the outgoing clip does not fade at all. If set to 0, the outgoing and incoming clips will dissolve smoothly throughout the transition.

Combine: Popup menu,  Default: From Over To .
By default the outgoing From clip scrambles away, revealing the To clip scrambling in underneath it. Set this to To Over From to have the To clip scramble in on top of the From clip. Adjusting Scramble Rel From and Scramble Rel To along with this can give nice results.
From Over To: Composites the From (outgoing) clip over the To (incoming) clip, which reveals the To clip as the From clip scrambles away. Works well with default settings or with Scramble Rel To set to zero.
To Over From: Composites the To (incoming) clip over the From (outgoing) clip, which scrambles the To clip in over the From clip. Works well with default settings or with Scramble Rel From set to zero.

Seed: Default: 0.5, Range: 0 or greater.
Used to initialize the random number generator for tiling the clips. The actual seed value is not significant, but different values will give different results.
See general info for: Crop/Transform , Motion Blur , Resolution , Clamp Output To Legal , Bypass Effect , and Reset .


See Also:

DissolveStatic
DissolveSpeckle
DissolveDiffuse
DissolveBubble
DissolveWaves
DissolvePuddle
DissolveVortex
DissolveBlur
DissolveDefocus
DissolveLuma
DissolveFilm
DissolveDistort
DissolveGlow
DissolveLensFlare
DissolveEdgeRays
DissolveGlint
DissolveGlintRainbow
TileScramble
Sapphire Plug-ins Introduction

PRODUCT UPDATES & SPECIAL OFFERS

Join our email newsletter and keep up to date